ALLCHIN SINGLE CYLINDER - TRACTION ENGINE

ALLCHIN SINGLE CYLINDER - TRACTION ENGINE
1 1/2" Scale Allchin 7nhp Single Cylinder General Purpose Traction Engine.
The ever popular Allchin in 1 1/2" scale suitable for most small work shops.




More Details >>

Versions available:
2 req GM RH & LH HIND HUB CENTRE - A 32
1 GM LH & RH HUB INSIDE END - A 33
Not used - A 34
Not used - A 35
2 req GM CHECK ANGLES - A 36
2 req AL HIND WHEEL - A 37
1 GM ANGLE RING FOR SPUD PAN - A 38
1 GM FORE CARRIAGE FORK ) - A 39
1 GM TURN TABLE - A 40
1 GM CYLINDER - A 41
1 GM VALVE CHEST - A 42
1 CI FLYWHEEL - A 43
1 GM PISTON - A 44
1 GM CYLINDER FRONT COVER - A 45
1 GM CYLINDER BACK COVER - A 46
1 GM CYLINDER LINER - A 47
1 GM TRUNK GUIDE - A 48
1 GM CROSSHEAD - A 49
1 GM MOTION BKT. - A 50
1 GM SAFETY VALVE COLUMNS - A 51
1 GM SLIDE VALVE - A 52
1 GM VALVE BUCKLE - A 53
2 req GM REGULATOR GLANDS - A 54
1 GM VALVE ROD GLANDS - A 55
2 req GM BIG END BRASSES (PAIR) - A 56
2 req GM ECCENTRIC STRAPS - A 57
1 CI SMOKE BOX BOILER RING - A 58
1 CI SMOKE BOX DOOR RING - A 59
1 CI SMOKE BOX DOOR - A 60
1 CI CHIMNEY SADDLE - A 61
1 CI CHIMNEY BOTTOM RING - A 62
1 CI CHIMNEY - A 63
1 GM BLAST PIPE - A 64
1 GM STEAM MANIFOLD - A 65
1 GM WATER PUMP BODY - A 66
1 GM PUMP ECCENTRIC STRAP - A 67
1 GM PUMP FEED CHECK VALVE - A 68
1 GM PUMP GLAND - A 69
1 GM COVER FLANGE - A 70
1 GM DELIVERY FLANGE - A 71
1 GM STEERING WHEEL - A 72
1 GM LUBRICATOR PLATFORM - A 73
1 GM GOVERNOR STAND & CAGE - A 74
1 GM BRAKE BKT. - A 75
1 GM BRAKE HANDWHEEL - A 76
2 req AL FRONT WHEELS - A 77
2 req GM FRONT HUB INSIDE ENDS - A 78
2 req GM FRONT HUB CENTRES - A 79
2 req GM FRONT HUB OUTSIDE ENDS - A 80
2 req GM FRONT HUB CAPS - A 81
BRASSES - A 150
ROLLED SMOKE BOX - A 158
CRANK BLANK - A154
SPOKES FRONT - Spokes are Laser cut clean and accurate. - A 155
SPOKES REAR - Spokes are Laser cut clean and accurate. - A 156
AXLE BLANK - A 157
HORNPLATES - Hornplates are Laser cut clean and accurate. - A 165
BOILER, COPPER - poa - A 163
BOILER KIT flanged - poa - A 164
2 req GM RH & LH HUB OUTSIDE END - A 31
1 CI DRIVING BOSS FOR RIGHT HIND WHEEL - A 30
1 GM COMPENSATING CENTRE - A 29
1 CI CENTRE FOR RH BEVEL WHEEL - A 28
1 Al SMALL FOOT STEP - A 1
1 Al LARGE FOOT STEP - A 2
1 GM DUMMY WATER POCKET - A 3
1 GM DUMMY WATER POCKET LID - A 4
1 GM STAND PIPE FOR WATER LIFTER - A 5
1 GM RH BEARING BKE. 3rd SHAFT WITH PUMP - A 6
1 BM LH BEARING BKT. 3rd SHAFT - A 7
1 GM QUADERANT FOR GEAR CHANGE - A 8
1 GM LH BEARING BKT. CRANK & 2nd SHAFT - A 10
1 GM RH BEARING BKT. CRANK & 2nd. SHAFT - A 9
1 GM REGULATOR QUADRANT - A 11
4 GM BEARING FOR CRANKSHAFT & 2nd SHAFT - A 12
4 GM KEEPS - A 13
2 req GM BEARINGS BKT FOR HIND AXLE - A 14
2 req GM DUMMY SPRINGS - A 15
1 GM CENTRE FOR 2nd. MOTION PINION - A 21
1GM CENTRE FOR 3rd. MOTION PINION - A 22
1 GM CENTRE FOR CHANGE SPEED SPUR WHEEL - A 23
1 CI BRAKE DRUM & CENTRE FOR 2nd. MOTION SPUR WHEEL - A 24
1 CI WINDING DRUM - A 25
1 CI DRIVING BOSS FOR WINDING DRUM LH - A 26
1 SET OF ROAD GEARS MACHINED AND GEAR CUT- INC 8 SPUR & 4 BEVELS & PINIONS - A 190
DRAWINGS - A166